YAMAHA TF1

โพสต์เมื่อ : 26 ส.ค 2567 เวลา 15:23 น.

ยี่ห้อ : YAMAHA

รุ่น : TF1

ราคาปกติ : ~~168,750.00~~ บาท

ราคาพิเศษ : 135,000.00บาท

รายละเอียดย่อ : YAMAHA TF1 ดิจิตอลมิกเซอร์ 40 input mixing channels (32 mono + 2 stereo + 2 return)

ราคาพิเศษ สอบถามโทร 080-6144774 , 02-9810944

รายละเอียดทั้งหมด

YAMAHA TF1 ดิจิตอลมิกเซอร์ 40 input mixing channels (32 mono + 2 stereo + 2 return)

17 motor faders (16 channels + 1 master)

40 input mixing channels (32 mono + 2 stereo + 2 return)

20 Aux buses (8 mono + 6 stereo) + Stereo + Sub

8 DCA groups with Roll-out

16 analog XLR/TRS combo mic/line inputs + 2 analog RCA pin stereo line inputs

16 analog XLR outputs

34 x 34 digital record/playback channels via USB 2.0 + 2 x 2 via a USB storage device

1 expansion slot for NY64-D audio interface card

Specs

General specifications

Sampling frequency rate Internal 48 kHz
Signal delay Less than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz
Fader 100 mm motorized, Resolution = 10-bit, +10 dB to –138 dB, –∞ dB all faders
Total harmonic distortion Less than 0.05% 20 Hz–20 kHz @+4 dBu into 600 , INPUT to OMNI OUT, Input Gain=Min. (Measured with a –18 dB/octave filter@80 kHz)
Frequency response +0.5, –1.5 dB 20 Hz–20 kHz, refer to +4 dBu output @1kHz, INPUT to OMNI OUT
Dynamic range 110 dB typ., DA Converter, 107 dB typ., INPUT to OMNI OUT, Input Gain=Min.
Hum & noise level Equivalent input noise –128 dBu typ., Input Gain=Max. (Measured with an A-Weight filter)
Residual output noise –85 dBu, ST master off (Measured with an A-Weight filter)
Crosstalk –100 dB (Measured with a –30 dB/octave filter@22 kHz), adjacent INPUT/OMNI OUT channels, Input Gain=Min.
Power requirements 100–240 V 50/60 Hz
Power consumption 100 W
Dimensions W 510 mm (20.1in)H 225 mm (8.9in)D 599 mm (23.6in)
Net weight 13.5 kg (29.8lb)
Accessories Quick Guide, Power Cord, CUBASE AI download information
Options Rack-mount Kit RK5014, Expansion Card, Foot Switch (FC5)
Others Operating temperature range: 0–40 °C, Storage temperature range: -20–60 °C

Analog input characteristics

Input Terminals GAIN Load
Impedance For Use With
Nominal Input Level Connector balanced /
Unbalanced
Sensitivity*1 Nominal Max. before clip
INPUT1-16 +66dB 7.5KΩ 50-600Ω Mics
or 600Ω Lines -82dBu (61.6V) -62dBu (0.616mV) -42dBu (6.16mV) Combo Jack (XLR-3-31 type *2
or TRS phone *3) Balanced
-6dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
ST IN 1,2 — 10kΩ 600Ω Lines -30dBV (31.6V) -10dBV (316mV) +10dBV (3.16V) RCA Pin Jack Unbalanced
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.)
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND
*In these specifications, 0dBu = 0.775Vrms.
*+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.

Analog output characteristics

Output Terminals Source
Impedance For Use With
Nominal GAIN SW Output Level Connector balanced /
Unbalanced
Nominal Max. before clip
OMNI OUT 1-16 75Ω 600Ω Lines“+24dBu” position (default)+4dBu (1.23 V) +24dBu (12.3 V) XLR-3-32 type *1 Balanced
PHONES *3 100Ω 40Ω Phones — 3mW 75mW Stereo Phone Jack (TRS) *2 Unbalanced
*1.1: GND,2: HOT, 3: COLD
*2 Tip: LEFT, Ring: RIGHT, Sleeve: GND
*3 The position of the level control is lowered by 16dB from the maximum.
*In these specifications, 0dBu = 0.775Vrms.
*All output DA converters are 24bit, 128times oversampling.

Digital input/output specifications